Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Dallas: What to Know First
We provide independent Olympia Chimney chimney liner and rebuild service in Dallas, typically completing liner replacements in one day and partial rebuilds in two to three days depending on weather. Every job starts with a written price before any work begins - no exceptions, no surprises after we’re on your roof. This page is for Olympia Chimney owners in Dallas, Lakewood, Lake Highlands, and surrounding neighborhoods who need straight answers about what’s failing, what it costs, and whether it can wait. Call (972) 284-1392 for a free estimate or a free second opinion on any written quote you’ve already received.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney ProFlex series flexible liners develop accordion creasing at the first offset below the smoke chamber, especially in Dallas homes built 1965-1985 with 8×12 clay flue tiles and a 30-degree bend. The creasing traps moisture from our humid Gulf-front air and accelerates pitting from the inside out. We pull the damaged section, measure the offset with a laser, and replace with a correctly sized ProFlex or DuraFlex equivalent with proper tension collars - not a generic flex jammed through and forgotten.
- Olympia Chimney rigid stainless 316Ti liners in two-story Highland Park and Preston Hollow installs often show weld-seam separation at the mid-chimney joint, visible on camera as a hairline gap that opens under heat cycling. The symptom is a faint smoke odor on windy days, not a full backup. We cut back to sound metal, re-weld with 316Ti filler, and sleeve with an expansion joint rated for Texas temperature swings - or replace the section if the gap has propagated.
- Olympia Chimney Gelco-compatible top-mount dampers seize in the open position after three to five seasons of cedar and post oak burning, common in Lakewood and East Dallas. The cast-aluminum frame warps slightly, the chain jams, and the homeowner doesn’t notice until the AC bill spikes. We document the warp with photos, quote a damper rebuild or replacement with a stainless frame, and include the repair in the liner scope if the flue is already being pulled.
- Olympia Chimney oval-to-round adapters on fireplace insert installs crack at the weld where the oval section meets the round riser, a known stress point when the insert is oversized for the firebox. The crack leaks combustion gases into the smoke chamber and shows up as warm spots on our thermal scan. We replace with a heavier-gauge adapter, properly relieve the stress with a flex section, and re-seal the surround - never just caulk over the crack.
- Olympia Chimney terra cotta flue liners in original Dallas construction spall and flake from the inside when paired with a gas insert retrofitted in the 2010s. The lower flue temperatures keep condensation on the clay surface, and the freeze-thaw of our occasional hard winters pops surface chips that fall and block the throat. We camera-map the damage, quote a stainless liner with proper insulation per NFPA 211, and show you the photos before you decide.
Our Olympia Chimney Chimney Liner & Rebuild Process
- 1
Call and schedule. A live person answers, checks availability, and notes your Olympia Chimney model if you know it. We don’t require it - our techs identify the line on site.
- 2
NFPA 211 Level 2 inspection with camera. Corrine Halstead and our crew have been running camera-down-the-flue inspections since 2009. On Olympia Chimney systems, we pay particular attention to the flex-to-rigid transition and the top-seal condition, both common failure points in Dallas’s clay-heavy soil and shifting foundations. You get a photo record on the spot - Clause 4 of the Haven Standard.
- 3
Written price, written scope, written warranty. Before any tool touches your chimney, you receive a flat price with line-item breakdown: parts, labor, disposal, and what happens if we find additional damage. No “call for a quote.” No verbal ballpark that balloons.
- 4
Parts procurement through Haven buying network. We source Olympia Chimney OEM, DuraFlex, HeatShield, or Gelco depending on what’s actually available and what’s honestly better for your specific failure. We explain the choice and show you the part before installation.
- 5
Installation and live test. Liner is pulled or rigid sections are welded, sealed, and pressure-tested or smoke-tested per manufacturer spec. On rebuilds, we cure masonry per temperature and humidity conditions - Dallas in August needs different timing than Dallas in February.
- 6
Final documentation and cleanup. You receive the completed photo record, the warranty card, and the 365-Day Done Right Promise in writing. Camera goes in first. Everything else follows.
Before
AfterWhat Olympia Chimney Chimney Liner & Rebuild Costs in Dallas
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Olympia Chimney flexible liner replacement (single flue, standard height) | $2,400 - $3,800 | Flue length, number of offsets, insulation required, access (steep roof, tight chase) |
| Olympia Chimney rigid 316Ti liner replacement | $3,200 - $5,100 | Diameter, story height, weld repairs vs. full section replacement, top-seal hardware |
| Partial chimney rebuild (crown, top 4-6 courses, liner pull) | $4,500 - $7,800 | Brick matching, scaffold needs, extent of water damage below the visible failure |
| Full chimney rebuild with new Olympia Chimney-compatible liner | $8,500 - $14,000 | Height, footing condition, chase enclosure rebuild, permit requirements |
| Olympia Chimney liner repair (sectional weld, adapter replacement) | $680 - $1,400 | Accessibility, whether the flue is already being accessed for other work |
These are real Dallas-market prices for work done under the Haven Standard, with background-checked technicians and a written warranty. We don’t bait with a low number and add charges later. Call (972) 284-1392 for an exact quote - estimates are free.
Why Dallas Homeowners Call Level Two Chimney Dallas for Olympia Chimney Work
We’ve completed more than 38,000 chimney inspections and cleanings since 2009, every one with a written price before work started and a documented record when done. The 365-Day Done Right Promise means if it’s not right, we make it right - no argument, no paperwork fight. Our technicians are background-checked, uniformed, and named before they arrive; you get a text when they’re on the way. We know Olympia Chimney’s product lines because we’ve pulled and replaced them in Dallas homes from Lake Highlands to Kessler Park, and we carry DuraFlex, HeatShield, and Gelco as alternatives when OEM isn’t the honest choice. Free second opinion on any written estimate. Live person on the phone, 24/7.
FAQs
No - but only if the work is done to NFPA 211 standards with compatible materials. As an independent Olympia Chimney service provider, we document every step with photos and manufacturer spec sheets so you have evidence the work was done correctly if a warranty question ever arises. We don’t cut corners that put your coverage at risk. Call (972) 284-1392 if you want us to review your warranty language before we start.
A properly installed Olympia Chimney stainless liner in Dallas typically lasts 15 to 25 years, but we’ve seen ProFlex units fail in 8 years when paired with oversized inserts or poor draft conditions. The bigger factor is maintenance: a liner inspected and swept every one to two years lasts significantly longer than one neglected until smoke backs up into the living room. Call (972) 284-1392 to schedule an inspection and see what condition yours is in.
We stock common Olympia Chimney adapters, collars, and top-seal hardware through our Haven buying network, and we cross-reference DuraFlex and Gelco equivalents for same-day completion when OEM is backordered. We don’t leave your chimney open overnight because a part is sitting in a warehouse in Ohio. Call (972) 284-1392 to confirm availability for your specific model.
The camera decides, not a sales pitch. If the liner damage is localized - a cracked adapter, a separated weld, a 12-inch section of creased flex - repair is honest. If the clay flue is spalled throughout, the chimney structure is leaking, or the liner has shifted due to foundation movement common in Dallas’s clay soils, rebuild is the only safe option. We show you the footage and explain which category you’re in before quoting either. Call (972) 284-1392 for a free inspection.
A compromised liner leaks heat and combustion gases into surrounding framing, increasing fire risk and potentially introducing carbon monoxide into living spaces. In Dallas’s tight, energy-efficient homes built 2015-2025, that risk is concentrated because there’s less air exchange. The damage also accelerates: a small flex crease becomes a tear, a hairline crack becomes a gap. That said, we don’t invent urgency - if the camera shows damage that can safely wait a season, we say so. Call (972) 284-1392 and we’ll tell you exactly where you stand.
Written by Corrine Halstead, Owner, Level Two Chimney Dallas at Level Two Chimney Dallas, serving Dallas and nearby areas.